Dyson V10 Parts Diagram & Details

Dyson V10 Parts and Functions are a lot to take in. There are so many parts that you need to know about, and it can be hard to keep track of everything. That’s why we’re here to help!

In this post, we’ll show you the different parts of Dyson V10 vacuums, including the floor nozzle, trigger, wand, handle, self-adjusting cleaner, and so on.

Dyson V10 Parts Diagram

dyson v10 parts diagram 2

Dyson V10 Parts Explained

dyson v10 parts diagram 1

Floor Nozzle

The floor nozzle is a large, black cylinder with a soft rubber head that’s used to remove dirt from your floor. It has a long, thin wire attached to it so you can easily vacuum it around corners and under furniture.

The nozzle itself has three different attachments: one has a wide brush on it; another has two smaller brushes facing each other at an angle, and the third attachment is designed for cleaning rugs.

The floor nozzle is located in the center of your vacuum, and it’s used to clean hard-to-reach places. The floor nozzle has two settings: low and high. You can use this feature to clean up dust, dirt, or pet hair easily without having to move furniture around first. This will save you time by not having to move furniture with your vacuum cleaner before cleaning up where you need it most!

Wand Handle

The wand handle is the part of your Dyson that you hold to guide the vacuum. It’s made of soft grip material, so it’s comfortable to hold and easy on your hands when you need to maneuver around furniture or obstacles.

The wand has a trigger on one end, which activates the vacuum head (the part that sucks). You simply press this button down for one second until there’s no more resistance from it being pressed; then release and let go of it once again.

This will then activate whatever mode (carpet/bare floor) that you selected earlier in our review process; however, if something gets stuck on top of this mechanism (like pet fur), release pressure from both sides at once before releasing any buttons again!

Self-Adjusting Cleaner Head

The Dyson V10 self-adjusting cleaner head is a great addition to your vacuum. It allows the cleaner head to adjust to the surface being cleaned, so you can sweep up dirt from hardwood floors without damaging them.

Bin Release Catch

The Bin Release Catch is a small, round piece of plastic that sits on the inside of your Dyson V10. This catch allows you to open and close your bin, which helps you keep track of how much trash has been collected in your bin over time.

The purpose of this part is to make sure that when you want to empty out your trash can quickly but don’t want it falling out onto the floor, there’s an easy way for them to do so without having any problems with dropping their contents all over everything else around them!

How does it work? It’s simple: just pull down on both sides at once until they click into place together; then lift up slightly so they’re still connected but not locked into place; then lift up again until they pop back out completely free-floating like normal before dropping whatever garbage needs cleaning back into its designated receptacle once more.”


The cyclone is the heart of your Dyson V10. It’s a centrifugal separator that separates the dirt from air and sends it down to the bottom of your vacuum cleaner. To make sure this process happens as efficiently as possible, Dyson designed their cyclones to spin at a high speed—up to 30,000 revolutions per minute!

The motor that rotates this part can be found inside one end or both ends of your machine depending on which model you have purchased.

Bin Assembly

The bin assembly is the part of your Dyson V10 that holds all of the items you can empty. It’s made up of a battery compartment, which holds your battery, and a bin release catch, which opens and closes to allow you to empty the contents into your trashcan or compost bin.

The filter is located in the bottom portion of this unit; it collects dirt and dust that may have been left behind by other parts during normal operation. You’ll see two tabs on either side called “lid lifters” that help lift these parts up so they don’t get damaged over time due to being exposed directly underneath them all day long!

The motorhead rotates around freely once everything else has been removed so there shouldn’t be any obstacles preventing its movement – but if there are any issues here then please let us know immediately so we can fix them up as soon as possible!


The battery is located in the handle and is removable. It’s a rechargeable battery that charges in the docking station, which you can use with your phone or other devices when you’re not using Dyson V10.


The filter is a washable, reusable filter that keeps dust and dirt from entering your vacuum’s motor. You should replace the filter every 6 months or when it becomes clogged, whichever comes first.

Before replacing your Dyson V10 filter, remove all screws from your machine and unplug it from its power source (if applicable). Then use an old toothbrush to brush away any loose dirt stuck on both sides of each panel inside of it so you don’t damage them further while cleaning out whatever may have gotten stuck there during the previous usage!


The trigger allows users to control how much suction they want when using their Dyson V10 machine. It also has an auto mode which will automatically adjust suction depending on what type of floor surface you’re cleaning (hardwood vs carpet). This makes it easy for everyone from beginners who aren’t sure what kind of power level they need yet to unlike experts who know exactly how much pressure should be applied based on each task at hand.”


We hope you’ve learned more about the Dyson V10 parts and functions, and that you feel confident with your purchase. It’s a great machine that will help you keep your home clean! We know how hard it can be to find just the right vacuum cleaner for your needs, so we would love it if you left us some feedback in the comments below.

Leave a Reply